2021/11/02، 04:00 AM
Operation method of ozone aging test chamber
The content of ozone in the atmosphere is very small, but it is the main factor of rubber cracking. The ozone aging box simulates and strengthens the ozone conditions in the atmosphere, studies the law of the effect of ozone on rubber, and quickly identifies and evaluates the anti-ozone aging performance and anti-ozone agent of rubber The method of protection efficiency, and then take effective anti-aging measures to improve the service life of rubber products
Operation method:
1. Timing setting of ozone aging test chamber
When setting, it can be set by the "+""-" button on the timer panel (H: hour, M: minute, S: second), such as 2 hours and 30 minutes, set "02H30", and turn it on after setting Timing switch, press the power "ON" button, the device enters high temperature and constant temperature operation at this time, when the time is up, the device will automatically cut off the power.
2. The test chamber ozone test starts
Turn on the power of the green button. Adjust the temperature of the test chamber to 40 degrees, wait for the temperature of the test chamber to stabilize. Set the ozone meter to 0, wait 20 minutes and then turn on the ozone button. For instrument settings, please refer to the instrument manual;
During the humidity test, Wuhan Shangce reminds you to first check whether there is water in the water tank, and add water without water. Turn on the heat and humidity button. Adjust the test instrument to the required test temperature and turn on the refrigeration button.
Three, dynamic test of the test chamber:
Turn on the turntable button and the stretch button, and adjust the speed as needed. The exhaust button is opened when the ozone is exhausted to the outside at the end of the test.
Four, test chamber alarm temperature setting:
Press the instrument setting key "SET" for 5 seconds to enter the internal menu of the instrument:
AL1 (Alarm 1): Generally AL1=SV+15℃, this alarm works when the temperature is high, and the low temperature does not need to be set. Example: SV is 50℃, then AL1 is 65℃.
ATU (auto-tuning): Auto-tuning is 0000 means off, 0001 means on. This machine generally does not need auto-tuning when it is turned on. If a certain set temperature is difficult to be constant, turn on auto-tuning. During the auto-tuning process, the temperature in the box will fluctuate, which is a normal phenomenon.
UV Carbon Arc weather Meter
UV Aging Test Chamber
Ozone test chamber
The content of ozone in the atmosphere is very small, but it is the main factor of rubber cracking. The ozone aging box simulates and strengthens the ozone conditions in the atmosphere, studies the law of the effect of ozone on rubber, and quickly identifies and evaluates the anti-ozone aging performance and anti-ozone agent of rubber The method of protection efficiency, and then take effective anti-aging measures to improve the service life of rubber products
Operation method:
1. Timing setting of ozone aging test chamber
When setting, it can be set by the "+""-" button on the timer panel (H: hour, M: minute, S: second), such as 2 hours and 30 minutes, set "02H30", and turn it on after setting Timing switch, press the power "ON" button, the device enters high temperature and constant temperature operation at this time, when the time is up, the device will automatically cut off the power.
2. The test chamber ozone test starts
Turn on the power of the green button. Adjust the temperature of the test chamber to 40 degrees, wait for the temperature of the test chamber to stabilize. Set the ozone meter to 0, wait 20 minutes and then turn on the ozone button. For instrument settings, please refer to the instrument manual;
During the humidity test, Wuhan Shangce reminds you to first check whether there is water in the water tank, and add water without water. Turn on the heat and humidity button. Adjust the test instrument to the required test temperature and turn on the refrigeration button.
Three, dynamic test of the test chamber:
Turn on the turntable button and the stretch button, and adjust the speed as needed. The exhaust button is opened when the ozone is exhausted to the outside at the end of the test.
Four, test chamber alarm temperature setting:
Press the instrument setting key "SET" for 5 seconds to enter the internal menu of the instrument:
AL1 (Alarm 1): Generally AL1=SV+15℃, this alarm works when the temperature is high, and the low temperature does not need to be set. Example: SV is 50℃, then AL1 is 65℃.
ATU (auto-tuning): Auto-tuning is 0000 means off, 0001 means on. This machine generally does not need auto-tuning when it is turned on. If a certain set temperature is difficult to be constant, turn on auto-tuning. During the auto-tuning process, the temperature in the box will fluctuate, which is a normal phenomenon.
UV Carbon Arc weather Meter
UV Aging Test Chamber
Ozone test chamber
